I bought it, and it sat for about a year.

I’ve been blasted at work and the love of the pins entered into burn out stage
and while I was still looking to acquire pins, I wasn’t looking hard.

I had planned to be at the showdown today, with the pins. That didn’t happen
because even after I got the hand working (using a 8 cent 3/8 corse thread nut)there were electrical issues that I had to work out.

So the day I was planning on just playing other peoples machines, taking photosand being in Denver, I spent slowly nursing a neglected pin back into health
and increasing my troubleshooting skills (and putting my TOP vid to good use )

This evening, as I was playing the game which works, minus a Actuator I need to
buy, I realized that while I would love to be in Denver right now, looking at
all the parts and goods, and most of all pins. That I love working on pins,
that I get a lot of satisfaction from working on these pins.

I am looking forward to grabbing some parts, and Pestering Scot Bogart, listening to some Chats, and playing some pins.

I love this hobby.

1. They are awesome.
2. They are not ready to bolt right back on. Plastic must be removed, and decals must be put on.
3. The plastic is soft, so it’s easy to work with.
4. They are awesome. So pretty; so, so pretty.

All the ramps need to have the screw holes countersunk, or chamfered, to accommodate the ramp screw heads. I got a chamfer bit and twisted it by hand.

The lower to upper ramp is too thick where it mates to the Upper playfield. Remove about 1/16 inch of plastic from the underside of the ramp where it sits on the Upper PF. If you don’t, there is a lip that the ball hits and will cause airballs. I got a file and carefully removed enough material that it was flush with the Upper PF.

The lower to upper is also just a bit shorter than original. No problem here, really. The ramp just sits about 1/2 inch further back. You can see how the ramp flap is sitting pretty close to the edge of the artwork.

Putting the decals on isn’t hard, as long at you use a little Windex to make sure you can reposition if necessary. I rubbed a Q-tip dipped in Windex on the ramp and it worked great. I could remove the decal if needed, and there was enough “stick” left that the decal didn’t wander.

If you replace the decals on Insanity Falls, they will never lay flat. Ever. The facory decals didn’t lay flat either. The bottom of the IF ramp isn’t flat, and has complex curves that no flat decal can match. They look fine, but without cutting or getting the decal folded up, you won’t get the edges of the decal to seal. Check out the pics of how mine came out.

On the middle of the ramp, you can faintly make out where the decal hasn’t sealed at some of the edges. I messed with it for a 1/2 hour before I realized it wasn’t going to happen. Looks much better than my old ones did.

I modified the Bigfoot Ramp guide plastic to prevent airballs from destroying the ramp switch. Removing the spacer lowers the plastic and keeps the ball on the ramp.

The VUK to the Upper PF had torn loose of it’s screws, and the op who fixed it did it by moving it over 1/4 inch and sinking new screws. I didn’t like this, so I drilled holes where the old, stripped mounting holes were and put in a screw with a bolt on the other side. It’s not coming loose again.

I also put a buffer wheel in my drill, and used Novus #3 and #2 to (almost) get rid of the ball trail on my Insanity Falls ramp. They were really bad, and I’m thrilled with how it turned out. This shot also shows how close I matched the replacement decal to the original that is stuck under the switch mount bracket rivets.

At the end of the Insanity Falls ramp, it looks like there should be a post to support it, but mine was missing. So I came up with this, and I think it’s pretty good. Maybe I’ll call it a “mod” and see if I can get someone to copy me.

This next shot show one of the new slingshot plastics from Phoenix Arcade. They are awesome. I put some 1″ lexan washers under them to (hopefully) keep them intact. After that is the jet bumpers with new rings and skirts.

And finally, a shot to show how far I’ve come. It’s huge, so don’t click it if you don’t really want to.

I replaced the backglass lift channel and the rear glass moulding. I also painted the wood the head sits on, the bottom U channel the DMD and speaker assembly sits in, and the top metal piece that sits above the head, whatever that is called.

I pulled the speakers out and cleaned the speaker grills from both sides. While I had the plastic DMD cover off, I got out the Novus #’s 3, 2 and 1 and got to work. It took 1/2 hour of hard rubbing, but it looks great! Cleaning the grills and brushing the dust off the speakers themselves brought back the deep black color, and the plastic DMD cover is now scratch free and clear as glass.

The inside of the coffin was dirty and scratched up, but not to the point that I was willing to repaint the whole thing. So I touched up the scrapes with a brush and called it good.

I painted the wood under the lockdown bar, in hindsight I’d use gloss black, rather than flat.

Next I cleaned up the front of the cab, put on the new coin door (should have got the 2 slot) and filled in the gouge above the shooter. I used the touchup paint that was supposed to match the decals, and it’s not even close. Looks way worse in person. I’m definitely re-doing that. Still, much better than before.

To finish up the cabinet work, I cleaned up the sides with a Magic Eraser and replaced the flipper buttons. I polished the legs and put a set of dark blue Pincab protectors on, mainly to hide the scrapes in the decals around the legs.

Underneath, I unscrewed all the targets and loosened the flipper bats. The replacement targets got soldered in, and all others got cleaned up so they look nice again. Soldering in the targets was tougher than I anticipated, as there is nothing to push against when they are just dangling from a vertical playfield.
Next was removal of all the lamp housings so I can clean the inserts from underneath. Out comes the alcohol and Q-tips, and I can’t believe what a difference it makes. I stuck a 40 watt work light in the cab and lowered the playfield to bask in the awesome. I see 2 inserts that didn’t get cleaned; they looked dim and dingy compared to the clean ones.
While I was down there I replaced all of the bulbs, just for good measure. I’d ordered 9 boxes each of #44 and #555 bulbs, might as well use them.

Back up top, the now bare playfield gets some attention. There is some slight insert wear that can be cleaned up using black and white paint, so that gets taken care of. I bought a nice, fine point sable brush and some black and white Model Master paint at a hobby store. If I do say so myself it looks pretty good.

It’s hard to see from pictures, but just the little bit on touchup I did makes a difference. The PF was in pretty good shape anyway, and fixing the black around the inserts makes the wear that’s still there less noticeable.

There was also this weird little hole in the PF, almost like it had been drilled. I painted it, then filled it with Krazy Glue. The glue I use is very thin, like water, so it files holes without leaving bubbles. It also runs down into cracks in plastics and bonds them solidly. it took several applications of glue to fill the hole, and then some sanding to get it flat. Now, if you aren’t looking for it, you’d never know it was there.

After that dries, 3 coats of Kit paste wax get put on and buffed to a nice shine. Mmmm. Glossy.

It still had the factory mylar on it, which was good. Except where it was worn through, which was bad. That VUK has done a number on the playfield.

So I froze the mylar off, and used Goo Gone to clean up the left behind adhesive. Then a little elbow grease, Novus and sandpaper took care of the rest. Tada!

No one will mistake it for NOS, but it’s much better than before. Cleaning the bottom sides of the inserts with alcohol and Q-tips made a huge difference too. Light can actually come through them now!

So without further ado, the list:

1. Ramps, full set of repros. Everything but Insanity Falls.
2. Plastics, full set of repros.
3. Topper Dome. Repro.
4. Waterfall topper insert. Beg, borrow, steal, wait patiently, pay way too much. Probably in that order.
5. Green translucent targets.
6. White targets
7. Coin door
8. Leg protectors
9. Coffin speaker
10. Backglass lift rail
11. Rear glass moulding
12. Leg bolts
13. Shooter rod components
14. Jet bumper skirts, and the ring and rod assembly.
15. Flasher domes, changing from red to blue
16. Pinballs
17. Star posts and plastic post sleeves, changing from clear to blue
18. Eproms – LH-5 for freeplay and added settings like ball save.
19. Bulbs of all varieties
20. Rubber kit.

Total cost: $76.48. Including shipping.

And just so this isn’t a text only post, here is a pic of me snowmobiling.

There’s more, but these pics really tell the tale. Are you supposed to be able to see the lights under the Whirlpool? Cause, I kinda can. If I look really hard. And who the hell put the “Bigfoots Cave” Mountain on bass-ackwards?

Next step: Order up the needed parts.

More to follow.